重型紙箱封箱機普遍故障及解決方法
Common faults and solutions of heavy carton sealing machine
重型紙箱包裝后，都進生一個打箱，那麼就要使用封箱機來操作了，重型紙箱封箱機它的操作簡易，是一種經久耐用的包裝設備。是機械總會發生故障的情況下，那麼重型紙箱封箱機發生故障了大家如何來辦呢。下邊我們一起來了解下。
After heavy cartons are packed, there will be a dozen cartons, so it is necessary to use the sealing machine. The heavy carton sealing machine is easy to operate and is a kind of durable packaging equipment. When the machinery always breaks down, what should we do when the heavy carton sealing machine breaks down. Let's get to know each other.
封箱機操作簡易，因此許多操作便會由于操作不合理發生一些故障。
The operation of the sealing machine is simple, so many operations will have some faults due to unreasonable operation.
故障一，封箱機的夾釘產生不夠或姿勢很慢
Fault 1: the nail clamping of the sealing machine is not enough or the posture is very slow
緣故：內片損壞，螺釘松懈或前扣軸的部位造成錯動。
Cause: the inner plate is damaged, the screw is loose or the part of the front buckle shaft causes dislocation.
故障解決方法：拆換槍栓的內片或往上略微激發前扣軸或往下略微激發前扣軸，以后再各自試運轉一下機器。
Troubleshooting: remove and replace the inner plate of the bolt, or slightly excite the front buckle shaft upward or slightly excite the front buckle shaft downward, and then try to run the machine separately later.
故障二：液壓缸周邊非常容易漏汽
Fault 2: steam leakage is very easy around the hydraulic cylinder
緣故及解決方法：主要是行為主體底端環因為長期工作的耗費損壞，應立即拆換底端環。
Cause and solution: it is mainly that the bottom end ring of the actor is damaged due to the cost of long-term work. The bottom end ring should be removed and replaced immediately.
故障三：槍栓處非常容易漏汽
Fault 3: it is very easy to leak steam at the bolt
緣故及解決方法：關鍵可能是切斷閥環毀壞或電源開關座環毀壞，也應立即拆換。此外也有出氣口非常容易漏汽，可能是發動機活塞毀壞，留意立即拆換。
Cause and solution: the key may be the destruction of the shut-off valve ring or the seat ring of the power switch, which should also be replaced immediately. In addition, the air outlet is very easy to leak steam, which may be the damage of the engine piston. Pay attention to remove and replace it immediately.
故障四：傳動系統換沒法精定位
Fault 4: the transmission system cannot be precisely positioned after replacement
緣故：可能是塑鋼型材條或傳動系統扭簧無彈性。
Reason: it may be that the plastic steel profile strip or the torsion spring of the transmission system is inelastic.
解決方法：先拆下來槍栓組成，把扭簧梢再次裝上或替換一個新的塑鋼型材條和傳動系統扭簧。
Solution: first remove the bolt composition, install the torsion spring tip again or replace a new plastic steel profile strip and transmission system torsion spring.
之上便是重型紙箱封箱機普遍的故障及解決方法。
Above are the common faults and solutions of heavy carton sealing machine.
The wonderful content of this article is provided by heavy carton manufacturers. There are many wonderful contents on this website. You can click to enter more contents: http://www.ntlongfa.cn We have special customer service to answer your questions
